The Rowing Stroke Cycle: Part 4 – finish

Advertisements

Finishing the rowing and sculling stroke

The finish is the final part of the drive where the rower draws the handle(s) in towards his body.

The finish is also where the blade is taken out of the water.

The finish occurs at that point in the stroke when the boat is moving at its fastest and the blades change from applying pressure against the water in one direction to moving freely in the air in the opposite direction.

  • Imagine throwing a ball without being able to use your fingers at the end of the throw; trying to skip a stone without a flick of your wrist, jumping high without being able to stretch your legs out to your toes.

Rowing without an effective finish is the same. A good clean finish can add the last available fraction of acceleration to a good stroke.

  • Remember setting your bike upside down and putting your fingertips through the the spokes to spin the wheel. (See Catch)
  • What happened when you were too slow pulling your fingers out once the wheel was moving?
  • What happened when you didn’t pull your fingers straight out (at right angles)?

A bad finish can act as a handbrake slowing the boat and undoing much of the good work of the drive.

Benefits of a Good Finish

Holding the pressure on through to the end of the stroke accelerates the boat more each stroke. More acceleration during the drive means greater speed once the blades are released.

If all blades in a boat hold the pressure on for the same length of time the boat will remain balanced and stable. This provides a better platform for the crew. If the boat is steady as the crew extracts the blades it is easier to stay balanced.

A cleanly executed finish releases the boat to run on and sets up the rower for feathering smoothly and easily before moving fluently into the recovery.

Perils of a Bad Finish

In a bad finish the blades are inefficient and speed is lost and the unevenness of the work in the water upsets balance and poise.

If blades are not held in the water, at the same height as they were during the main drive, and are instead allowed to ride up as the finish is approached the rower is said to be washing out. This wastes energy by turning water to froth instead of propelling the boat and tends to pull that rigger down upsetting the balance. The water thrown up by such a finish often hits the blade of the rower next towards the stern and disrupts her recovery.

When a rower fails to apply sufficient force to the handle in the finish the puddle behind the oar closes up and the blade acts as a handbrake and slows the boat as the drive ends instead of carrying the acceleration on.

When a sculler or crew has differences in the finish from blade to blade and side to side balance is always compromised. The finish must inevitably apply vertical forces to the rigger as the blade is lifted from the water and if these are not equal between riggers the boat will be forced out of balance.

Drawing the handle in.

In order to produce a good finish the rower must be able to apply power to the handle throughout the stroke. The power for the last part of the drive sequence is provided by the muscles of the shoulders, upper back and upper arms.

To draw the handle to the appropriate height, usually around the first rib, the shoulders are opened, shoulder blades squeezed together, and the elbows drawn past the chest. This requires that the lower back is held firm to provide the base off which the upper body can work. The pelvis should be in the neutral position and the lumbar spine straight and aligned with the pelvis. The shoulders stay low and move only in the horizontal.

The inside arm and elbow move out a little from the body to keep the forearm at right angles to the handle and the outside elbow is allowed to move sufficiently far out from the body so that the elbow, wrist and top knuckles form a horizontal line.

The handle stops just before the body.

  • Sit on an ergo with your legs straight, holding the handle with your arms straight.
  • Now take your feet off the stretcher. Aaaah … now we see how good your core control is!
  • Once you are balanced draw the handle in towards you.
  • What happens?
  • Put your feet back on the footstretcher but without strapping them in. Leave your legs straight and draw the handle into your body.
  • How much sound comes from the flywheel?
  • Try again, this time pressing against the footstretcher with your feet as you draw your elbows past your body.
  • Hear that?
  • And again, starting the push on the whole of your foot on both feet and finishing stretched out to your toes as the elbows draw back. Your legs don’t move but you’ll feel the muscles in your thighs contracting as you stretch.
  • How’s that flywheel going now?

A good finish with lots of acceleration stays connected to the boat through the feet.

Read more about the finish including “Extracting the blade” and “The Sculling finish”

Read the other articles in the series…
Part I – Posture
Part II – Catch
Part III – Drive (Previous)
Part V – Recovery (Next)
Part VI – Grip

Advertisements

Subscribe to our Newsletter for more information:

Our Rowing Network

Did you like this post? Support this blog and our network by donating

Feel like Rowing again? Visit the Shop at coastal-boats.eu!

Shop
Accessories, equipment, boats, clothing

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Related Posts

Whether it’s sports, nutrition or equipment, you’ll find what you’re looking for in one of these categories

Categories

Everything about rowing – browse through our large archive or search for articles of your choice

Archive

Search Blog

Search

Rowing Network

Do you like our posts? Support this blog and our network by donating

Newsletter

Get all latest content and news!